Enter your Sprinter VIN below to filter the Brakes and Suspension catalogs to parts that actually fit your van.
Parts We Actually Recommend
Every part on this page is hand-picked based on real shop experience. OEM and trusted aftermarket options with honest notes on what to buy and why.
“Bad parts cost more in the long run — comebacks, repeat failures, and the labour to replace them again. Every part here is something I'd spec on a van I care about.”
Enter your Sprinter VIN
We'll decode your model year, platform (NCV3 or VS30/W907), GVW, and engine, then auto-filter the Brakes and Suspension catalogs so you only see parts that fit. Mercedes-Benz Sprinter only.
Brakes — Pads, Rotors, Sensors, Calipers & Fluid
Verified for 2019–Present Mercedes-Benz Sprinter 2500 VS30 (W907) with the 3.0L V6 OM642. Use the variant filters to show only the parts that fit your drivetrain and parking brake setup.
Several brake parts differ by drivetrain (4WD vs 2WD) and parking brake type (Standard vs Electric/EPB). Use the filter below to show only the parts for your van. When in doubt, contact us before ordering.
Brake Pads
Front Brake Pads
PN 906 421 15 00
Position: Front axle — 1 set
Qty: 1 set per axle
$96.99 – $142.99
Front brake pad set. Fits all 2019–2022 Sprinter 2500 VS30 regardless of drivetrain. Replace as a full axle set and inspect rotors at the same time.
Rear Brake Pads
PN 910 420 73 00
Position: Rear axle — 1 set
Qty: 1 set per axle
$85.99 – $136.99
Compatible with both standard and electric parking brake configurations. Confirm your parking brake type before ordering — the rear rotor differs between EPB and standard, but the pads are the same.
Brake Rotors
Front Rotors — 4WD Models
PN 907 421 01 00 07
Spec: Vented disc, 300 × 28 mm
Position: Front
Qty: Qty 2 required per axle
4WD ONLY. Different hat depth and hub bore from RWD. Will not fit 2WD models.
From $114.99 each — qty 2 per axle
Coated rotors resist surface rust during break-in. Replace in axle pairs. Always replace pads and rotors at the same service.
Front Rotors — 2WD / RWD Models
PN 910 421 00 00 07
Spec: Vented disc, 300 × 28 mm
Position: Front
Qty: Qty 2 required per axle
RWD / 2WD ONLY. Do not install on 4WD models.
From $114.99 each — qty 2 per axle
Replace in axle pairs. Always replace pads and rotors at the same service.
Rear Rotors — Standard Parking Brake
PN 910 423 02 00 07
Spec: Solid disc, 298 × 18 mm
Position: Rear
Qty: Qty 2 required per axle
For vans WITHOUT electric parking brake only. Not interchangeable with EPB rotor.
From $74.99 each — qty 2 per axle
Replace in axle pairs along with pads.
Rear Rotors — Electric Parking Brake
PN 910 423 21 00 07
Spec: Solid disc, 298 × 18 mm
Position: Rear
Qty: Qty 2 required per axle
For vans WITH electric parking brake only. EPB actuator geometry requires this specific rotor — the standard version will not work.
From $86.99 each — qty 2 per axle
Replace in axle pairs along with pads.
Brake Pad Wear Sensors
Consumable sensor clips that contact the rotor when pads reach minimum thickness, triggering the brake warning light. Replace at every brake service. Do not reuse.
Rear Brake Pad Wear Sensor
PN 639 540 14 17
Position: Rear
Qty: Without EPB: qty 1 per vehicle · With EPB: qty 2 (one per side)
$5.99 – $7.99
Standard parking brake: order qty 1. Electric parking brake: order qty 2. Always replace — reusing a worn sensor gives a false reading.
Front Brake Pad Wear Sensor
PN 906 540 15 17
Position: Front
Qty: Qty 1 per vehicle
$7.99
One per vehicle. Replace at every front brake service.
Brake Calipers
Front Caliper — Driver Side (Left)
PN 907 421 89 00
Position: Front Left
Qty: Qty 1
$418.99
Remanufactured OEM caliper. Core charge may apply — confirm at checkout. Replace as a pair with the passenger-side caliper for even braking. Inspect guide pins and boots at every brake service.
Front Caliper — Passenger Side (Right)
PN 907 421 90 00
Position: Front Right
Qty: Qty 1
$418.99
Replace as a pair with the driver-side caliper (907 421 89 00).
Brake Fluid
Brake Fluid — 1 Liter
PN 000 989 08 07 01
Spec: Mercedes DOT 4 / DOT 4 Plus — spec 331.0
Position: Hydraulic system
Qty: ~1 liter per flush
$20.99 – $25.99
Mercedes requires DOT 4 minimum (spec 331.0). Flush every 2 years regardless of mileage — brake fluid absorbs moisture over time, lowering its boiling point and accelerating corrosion in ABS module internals. Approximately 1 liter used per flush.
Brake Fluid — 5 Liter
PN 000 989 08 07 11
Spec: Mercedes DOT 4 / DOT 4 Plus — spec 331.0
Position: Hydraulic system
Qty: Bulk size for full flush + spare
$108.99 – $114.99
Bulk DOT 4 — economical for shops or owners running multiple vans.
Brake Fluid — DOT 4 LV Low Viscosity, 1 Liter
PN 706402
Spec: ATE SL.6 DOT 4 LV
Position: Hydraulic system
Qty: ~1 liter per flush
$28.99
Low-viscosity formula designed for vehicles with ABS and ESP hydraulic units. Recommended upgrade for all VS30 Sprinters.
Brake Fluid — DOT 4 LV Low Viscosity, 5 Liter
PN 706403
Spec: ATE SL.6 DOT 4 LV
Position: Hydraulic system
Qty: Bulk size
$104.99
Bulk DOT 4 LV — recommended for VS30 Sprinters.
Coming Soon
Brake Hose (4 corners)
Pricing & specs being finalised
Brake Caliper Guide Pin / Hardware Kit
Pricing & specs being finalised
Parking Brake Shoe Set (EPB models)
Pricing & specs being finalised
Brake Master Cylinder
Pricing & specs being finalised
Core charges on remanufactured calipers are confirmed at checkout. Prices exclude tax and shipping.
Suspension — Struts, Shocks, Control Arms, Tie Rods & Hardware
Verified for 2019–Present Mercedes-Benz Sprinter VS30 (W907) across 1500/2500/3500 and both 4WD and 2WD. Use the GVW class and drive type filters to narrow the catalogue to parts that fit your van.
Front Struts
MacPherson strut assemblies for the VS30 front suspension. The 4WD and 2WD parts are NOT interchangeable — confirm drivetrain before ordering.
Front Strut — 4WD (OEM Replacement)
- Part #:
- 906 320 14 33 64
- Spec:
- Bilstein B4 MacPherson strut, OEM-spec
- Position:
- Front
- Qty:
- Qty 2 per axle
OEM-spec replacement strut for 4WD Sprinter front axle. Always replace in pairs and reset alignment.
Front suspension service guideFront Strut — 2WD / RWD (OEM Replacement)
- Part #:
- 907 320 12 02
- Spec:
- Bilstein B4 MacPherson strut, OEM-spec
- Position:
- Front
- Qty:
- Qty 2 per axle
OEM-spec strut for the rear-wheel-drive VS30. Replace in pairs.
Front suspension service guideFront Strut — 4WD (Performance Upgrade)
- Part #:
- 22-285959
- Spec:
- Bilstein B6 performance strut
- Position:
- Front
- Qty:
- Qty 2 per axle
Bilstein B6 performance upgrade — firmer valving and improved body control. Popular for loaded cargo, camper conversions, and high-mileage rebuilds. Order qty 2 of strut mount 907 323 04 00 with replacement.
Front suspension service guideFront Strut — 2WD / RWD (Performance Upgrade)
- Part #:
- 22-310415
- Spec:
- Bilstein B6 performance strut
- Position:
- Front
- Qty:
- Qty 2 per axle
Bilstein B6 performance strut for RWD Sprinter. Upgraded valving over B4. Recommended for camper builds, loaded vans, and high-mileage replacement. Order new strut mounts with any strut replacement.
Front suspension service guideFront Strut Mounts
Front Strut Mount (Upper)
- Part #:
- 907 323 04 00
- Position:
- Front upper
- Qty:
- Qty 2 per vehicle
Upper strut bearing mount. Replace any time struts are replaced — worn mounts cause clunking and poor steering return.
Front suspension service guideRear Shock Absorbers
Rear shocks differ between 4WD and 2WD. The B6 camper-rate option is RWD-only and is purpose-built for heavily loaded vans.
Rear Shock — 4WD (OEM Replacement)
- Part #:
- 907 320 43 01
- Spec:
- Bilstein B4
- Position:
- Rear
- Qty:
- Qty 2
OEM-spec rear shock for 4WD Sprinter. Replace in pairs.
Rear suspension service guideRear Shock — 2WD / RWD (OEM Replacement)
- Part #:
- 907 320 79 01
- Position:
- Rear
- Qty:
- Qty 2
Two solid options — Sachs is the OEM supplier, Bilstein B4 is the OEM-match aftermarket.
Rear suspension service guideRear Shock — 2WD / RWD (Camper / Heavy Load)
- Part #:
- 24-310420
- Spec:
- Bilstein B6, camper-rate valving
- Position:
- Rear
- Qty:
- Qty 2
Bilstein B6 heavy-duty rear shock with valving developed specifically for camper conversions and loaded cargo. Stiffer damping prevents bottoming on uneven surfaces under load. RWD only.
Rear suspension service guideFront Control Arms
Lower control arms include the ball joint pressed in. If only the ball joint is worn, see the Ball Joints section for a press-in replacement instead.
Front Lower Control Arm — Driver Side (Left)
- Part #:
- 906 330 40 07
- Position:
- Front left
- Qty:
- Qty 1
Front lower control arm with ball joint. Replace when the ball joint is worn or when bushings are cracked or torn. Driver side.
Front suspension service guideFront Lower Control Arm — Passenger Side (Right)
- Part #:
- 906 330 41 07
- Position:
- Front right
- Qty:
- Qty 1
Passenger side. Replace in pairs with the driver side for even wear and predictable handling.
Front suspension service guideBall Joints
Press-in replacement option when only the ball joint is worn.
Front Ball Joint (Press-In)
- Part #:
- 55 0070 906
- Position:
- Front, one per control arm
- Qty:
- Qty 2
Symptoms of wear include clunking over bumps, uneven tyre wear, and loose or vague steering feel. Replace both sides at once.
Front suspension service guideControl Arm Bushings
Front Lower Control Arm Bushing — Rearward
- Part #:
- 906 333 01 14
- Position:
- Front, rearward bushing each side
- Qty:
- Qty 2 (one per side)
Rear-position control arm bushing — a common wear point causing front wander and clunking. Can be replaced independently if only this bushing is worn.
Front suspension service guideSway Bar (Stabilizer) Links
Front Sway Bar Link — Driver Side (Left)
- Part #:
- 907 320 04 01
- Position:
- Front left
- Qty:
- Qty 1 (replace in pairs)
Front sway bar end link, driver side. Worn links cause rattling or clunking over bumps and in corners. Replace in pairs.
Front suspension service guideFront Sway Bar Link — Passenger Side (Right)
- Part #:
- 907 320 05 01
- Position:
- Front right
- Qty:
- Qty 1 (replace in pairs)
Passenger side sway bar end link.
Front suspension service guideSway Bar Bushings
Front Sway Bar Bushing Bracket
- Part #:
- 907 326 46 00
- Position:
- Front
- Qty:
- Qty 2
Front sway bar bushing/bracket assembly. Worn bushings cause body roll and knocking on cornering. Replace with sway bar link service.
Front suspension service guideTie Rod Ends
4WD and 2WD use different steering systems. 4WD uses a solid front axle (Dana 30 carry-over) with inner/outer tie rods per side. 2WD uses a rack-and-pinion with separate left/right outers and inners. Parts are NOT interchangeable.
4WD — Inner Tie Rod End
- Part #:
- 906 460 01 55 64
- Position:
- Inner
- Qty:
- Qty 2
Inner tie rod end for 4WD solid-front-axle steering. Requires inner tie rod removal tool. Always check or reset alignment after replacement.
Front suspension service guide4WD — Outer Tie Rod End
- Part #:
- 906 460 03 48 64
- Position:
- Outer
- Qty:
- Qty 2
Outer tie rod end for 4WD. Failure causes loose steering, pulling, and uneven tyre wear. Alignment required after replacement.
Front suspension service guide2WD — Left Outer Tie Rod End
- Part #:
- 907 460 62 00 64
- Position:
- Front left outer
- Qty:
- Qty 1
Left outer tie rod for the RWD rack-and-pinion. Alignment required after replacement.
Front suspension service guide2WD — Right Outer Tie Rod End
- Part #:
- 907 460 64 00 64
- Position:
- Front right outer
- Qty:
- Qty 1
Right outer tie rod for the RWD rack-and-pinion. Alignment required after replacement.
Front suspension service guide2WD — Inner Tie Rod (Rack End)
- Part #:
- 907 460 63 00 65
- Position:
- Inner
- Qty:
- Qty 2
Inner tie rod / rack end for the RWD rack-and-pinion steering. Worn inner rods cause steering wander and wheel shimmy. Inner tie rod removal tool required. Alignment required.
Front suspension service guideWheel Lug Bolts
Length differs between steel and alloy wheels. Do not mix bolts — incorrect length causes improper seating.
Lug Bolt — Steel Wheel (M14×1.5, 58 mm)
- Part #:
- 000 990 24 07
- Position:
- All four corners
- Qty:
- Qty 24 (6 per wheel × 4)
Standard lug bolt for steel wheels. Sprinter uses 6 lug bolts per wheel.
Lug Bolt — Alloy Wheel (M14×1.5, 74 mm)
- Part #:
- 906 990 00 07
- Position:
- All four corners
- Qty:
- Qty 24
Longer lug bolt for alloy wheel fitment. Do not mix with steel-wheel bolts.
Coming soon
These parts are catalogued but not currently stocked at SSF for the VS30. Contact us for a quote and we'll source them through MB dealer or our specialist channels.
Rear Leaf Springs (2500)
Pricing reference — quote on request. Source separately for VS30; load rating differs from 3500.
Rear Leaf Springs (3500)
Heavier-rate leaf pack for 3500/3500XD GVW. Source via MB dealer or specialist.
Rear Spring & Shackle Bushings
Pricing reference — quote on request.
Rear Spring U-Bolts
Pricing reference — quote on request.
Rear Shackles
Pricing reference — quote on request.
Wheel Hub / Bearing Assemblies (Front & Rear)
Integral hub units — not available separately for VS30. Source via MB dealer (A 907 350 02 25), europaparts.com, or iDparts.com.
Bump Stops (Front & Rear)
Pricing reference — quote on request.
Steering Knuckle
Pricing reference — quote on request. Drive-specific (4WD vs 2WD).
Rear Sway Bar (3500 only)
Rear stabilizer bar fitted to 3500 / 3500XD only — not on 1500/2500.
Prices exclude tax and shipping. Always verify part numbers against your VIN and production date before ordering.
Maintenance & Fluids — Drain Hardware, Filters & Lubricants
Verified for 2019–Present Mercedes-Benz Sprinter VS30/W907 with the 3.0L V6 OM642. Spec-correct fluids with capacities, filter cross-references, and 4WD-specific items.
Verified for 2019–Present VS30/W907 Sprinter (3.0L V6 OM642).
Prices shown are MSRP-style retail and exclude tax, shipping, and labour. Items without a price are pending verified data — request a quote and we'll source the correct part for your VIN.
Engine drain & service hardware
Replace seals at every oil change. Confirm magnetic vs non-magnetic plug against your existing OEM part.
Replace if threads are damaged or the plug is non-magnetic. Magnetic drain plugs catch ferrous wear particles and should be confirmed against your existing OEM plug before swapping.
- Confirm OEM is magnetic before ordering an aftermarket replacement.
- Torque to spec — over-tightening cracks the oil-pan boss.
Verify part against your VIN before ordering.
Replace at every oil change. Re-using a crushed aluminum washer is the most common cause of oil-pan drain weeps.
Verify part against your VIN before ordering.
OEM oil filler cap with integrated O-ring. Replace if the seal is cracked or the cap no longer clicks home.
Verify part against your VIN before ordering.
Pan-mounted oil level / temperature sensor. Diagnostic codes for "Oil Level Implausible" usually trace back to this sensor or its harness connector.
Verify part against your VIN before ordering.
Fluids
Spec-correct fluids with capacities. Always cross-check the MB approval code on the bottle.
Full-synthetic low-SAPS oil meeting MB 229.52. Required for OM642 with DPF/SCR. Service interval ~10,000 mi or 1 year.
- Recommended brands: Mobil 1 ESP 5W-30, Liqui Moly Top Tec 4200, Pentosin Pento Hybrid.
- Replace oil filter and crush washer at every change.
Verify part against your VIN before ordering.
ATF meeting MB 236.14 spec — recommended brands are Liqui Moly Top Tec ATF 1600 or Mercedes-Benz Genuine ATF 236.14. Service interval is 40,000 mi under severe duty (towing, hot climate).
- Service kit (PN 55 8600 141) bundles filter, pan gasket, adapter plug, 6 pan bolts, drain plug, drain plug seal, and filler cap lock pin.
- Fill is fluid-temperature-dependent — verify with diagnostic tool.
Verify part against your VIN before ordering.
Synthetic hypoid gear oil meeting API GL-5 in 75W-90 viscosity. Confirm MB approval code (typically MB 235.0) against your owner's manual before ordering.
- Recommended: Liqui Moly Hypoid Gear Oil GL-5 75W-90 or MB Genuine 235.0.
- Replace fill plug crush washer at every service.
Verify part against your VIN before ordering.
4WD-only. Synthetic hypoid gear oil. Same spec as the rear differential on most VS30 4WD configurations — confirm against your owner's manual.
Verify part against your VIN before ordering.
4WD-only. Verify the exact MB approval code on your transfer case fill label — VS30 4WD systems use a specific spec, not generic ATF.
Verify part against your VIN before ordering.
Pentosin Super DOT 4 LV · 000989080713
Low-viscosity DOT 4 brake fluid required for VS30 stability-control and EPB systems. Standard DOT 3 / DOT 4 will cause warning lights and degrade pump life.
- Bleed sequence: rear-passenger → rear-driver → front-passenger → front-driver.
- Replace every 2 years regardless of mileage.
Urea solution for the SCR system. Use only ISO 22241-certified DEF (BlueDEF, AdBlue, MB Genuine). Aftermarket blends will set fault codes and disable starts under emissions logic.
- Low-DEF indicator triggers at ~12% remaining (~3,500 mi countdown).
- Do not over-fill — pressure-relief venting damages the tank.
Verify part against your VIN before ordering.
Hybrid OAT coolant meeting MB 325.5 (replaces older MB 325.0). Pre-mixed 50/50 with deionized water. Do NOT mix with green or pink coolants.
- Recommended: Zerex G05 or MB Genuine 325.5.
Verify part against your VIN before ordering.
Fuel filtration
VS30 OM642 typically uses a single primary heated filter. Verify connector type (3-pin vs 5-pin) on your existing filter before ordering.
Mann OEM · 6420906052
Primary fuel filter with integrated heating element and water-in-fuel sensor for 2019+ VS30/W907 OM642. Confirm 5-pin connector on your existing filter before ordering.
- Replacement interval: every 20,000–30,000 mi or with each Service A.
- Older 3-pin / non-heated variants exist on early NCV3 vans — DO NOT cross-fit.
Verify part against your VIN before ordering.
Some VS30 fleet configurations carry a secondary in-line fuel filter ahead of the high-pressure pump. Confirm presence on your van — many VS30 vans run only the primary heated filter.
Verify part against your VIN before ordering.
Prices exclude tax and shipping. Compatibility is referenced against a 2022 VS30 reference VIN — confirm against your own van's build sheet.
Full Sprinter Parts Reference
Every OEM and aftermarket part we've catalogued across the NCV3 and VS30 platforms. 62 parts across 12 categories. Click any row to see specs, applicable models, and where to buy.
Always verify part numbers against your VIN and production date before ordering. Many parts changed mid-model-year (e.g. glow plug revision 6/14/2012; fuel filter connector types). Pricing reflects parts cost + 40% service margin and excludes labour, tax, and shipping. Compatibility badges are based on a 2022 VS30 reference VIN — confirm against your own van.
Showing 62 of 62 parts
Oil Filter – OM642 3.0L V6
VS30 CompatiblePrimary engine oil filter for 3.0L V6 OM642 diesel; includes gasket. OEM Mann HU821X. Replace every service interval (~10,000 mi).
Oil Filter – OM642 (updated rev.)
VS30 CompatibleUpdated revision oil filter for OM642. Cross-reference to 6421800009. Check production date before ordering.
Oil Filter – OM651 2.1L I4
Not Compatible (OM651)Engine oil filter for 2.1L 4-cylinder OM651 diesel. Multiple revision p/ns: 651-180-01-09, 651-180-03-09.
Engine Air Filter (Mann C43121)
VS30 CompatibleEngine air intake filter for 2010+ models. OEM: A 000 090 37 51. Replace every 20,000–30,000 mi or as indicated.
Cabin Air Filter – VS30 (Hengst)
VS30 CompatibleCabin air/pollen filter for the 3rd-gen VS30 Sprinter. Hengst E4927LC for auto A/C (HH4) or E4927LI for semi-auto (HH9). Replace annually or every 15,000 mi.
Cabin Air Filter – NCV3 (charcoal-activated)
NCV3 OnlyRecommended OEM charcoal-activated cabin filter for NCV3. Captures diesel/exhaust odors, pollen, and fine particulates. Alt p/n 906-830-02-18.
Cabin Air Filter – W907 (charcoal-activated)
VS30 CompatibleRecommended OEM charcoal-activated cabin filter for W907/VS30. Significant upgrade over standard particulate filter for traffic and camper use.
Fuel Filter – VS30/W907 OM642 (heated, Mann OEM)
VS30 CompatibleOEM fuel filter for 2019+ VS30/W907 Sprinter with 3.0L V6 OM642. Includes integrated heating element and water-in-fuel sensor. Part of the VS30 Service A filter pack.
Fuel Filter – NCV3 OM642 (5-pin)
NCV3 OnlyLatest-revision fuel filter; 5-pin plug for water sensor & heater, 13 mm and 15 mm fuel lines. NCV3 build dates 2012-2018 ONLY. MUST verify against existing connector before ordering.
Fuel Filter – NCV3 OM651 2.1L
Not Compatible (OM651)OEM fuel filter for Sprinter with 2.1L I4 OM651. Does NOT fit OM642 V6 vans.
Water Pump – OM642 (7-groove)
VS30 CompatibleMechanical water pump for 3.0L OM642 with 7-groove pulley. OE supplier (Graf). Includes gasket. Common failure ~100k+ miles.
Water Pump – OM642 (updated)
VS30 CompatibleUpdated water pump revision for OM642. Includes new gasket. Confirm groove count and production date before ordering.
Water Pump – OM651 2.1L (switchable impeller)
Not Compatible (OM651)Switchable-impeller water pump for OM651. Failure can contaminate vacuum system; Mercedes specifies replacing vacuum reservoir and changeover valve simultaneously.
Auxiliary Electric Water Pump
Verify FitmentAuxiliary electric pump (alt p/n 2118350264) circulates coolant through heater core. Runs when ignition is on. Common NCV3 failure.
Thermostat Assembly – OM642 Late (unheated)
VS30 CompatibleUnheated thermostat assembly for late-model NCV3 OM642 and VS30. Verify heated vs. unheated variant for your build date.
Thermostat Assembly – OM642 Early (unheated)
NCV3 OnlyUnheated thermostat assembly for early NCV3 OM642 models. Check production date.
Thermostat Assembly – OM642 Early (heated)
NCV3 OnlyHeated thermostat (has electrical connector) for early OM642 NCV3. Verify by checking your existing part.
Serpentine Belt – OM642 (PK070801, 7-rib, 2035mm)
VS30 Compatible7-rib accessory drive belt for 2008+ OM642 NCV3/VS30. 2035 mm length. Replace if cracked, frayed, or at belt kit interval.
Serpentine Belt Tensioner – OM642
VS30 CompatibleINA OEM belt tensioner for 3.0L V6 OM642 drive system. Not for early 2007–some 2008 CDI ML/GL/R vehicles. Replace with belt.
Serpentine Belt Idler Pulley – OM642 (qty. 2)
VS30 CompatibleFlat idler/deflection pulley for the OM642 serpentine belt. INA OEM. Two required per vehicle. Replace bearings at belt service.
Aux Serpentine Belt Tensioner (Rear A/C or 2nd Alt)
Verify FitmentTensioner for secondary drive belt powering optional rear A/C compressor (N63) or secondary alternator (N62) on NCV3.
Alternator – Bosch Reman 220A (OM642)
VS30 CompatibleBosch remanufactured 220A alternator for the OM642 V6 - the recommended replacement when full capacity is required (cold-climate use, dual-battery house systems, conversions). Direct fit, OEM connector.
Alternator – Valeo 220A (OM642 OE)
VS30 CompatibleOriginal-equipment Valeo 220A alternator. Stock fitment on most OM642 vans. Direct replacement using existing wiring.
Alternator – Valeo 180A (OM642 base)
VS30 CompatibleLower-output 180A alternator used on base/non-cold-package OM642 vans. Acceptable for stock loads; upgrade to 220A if running a house battery, inverter, or rear A/C.
Glow Plug – OM642 7V Ceramic (post 6/14/2012)
VS30 Compatible7V ceramic glow plug (NGK CZ303) for OM642 V6. NCV3 switched to 7V plug after build date 6/14/2012; correct plug for 2019-2022 VS30. Replace all 6 together.
Glow Plug – OM642 Early 4.4V
Pre-2012 OnlyEarlier-spec glow plug for 2007–mid-2012 OM642. OEM p/n 001-159-71-01-64. NOT for 2019-2022 VS30. Plugs can seize in the head; use anti-seize on install.
Glow Plug Control Module – OM642
VS30 CompatibleGlow plug control module/relay. Original design prone to blown fusible links; updated solid-state revision available. Replace when faulted.
Front Brake Pads – Sprinter 2500
VS30 CompatibleOEM front disc brake pad set for Sprinter 2500. Alt p/n 0054205220. Includes wear sensor where applicable.
Front Brake Pads – Sprinter 3500
VS30 CompatibleOEM front disc brake pad set for Sprinter 3500. Includes wear sensor. Replace pads and rotors together for best results.
Front Brake Rotor – Sprinter 3500 (qty. 2)
VS30 CompatibleFront ventilated brake rotor for Sprinter 3500. Sold individually; qty. 2 needed per axle. Inspect for minimum thickness.
Rear Brake Pads – Sprinter NCV3/VS30
VS30 CompatibleOEM rear brake pad set. Alt p/n 9064210700. Verify fitment by model (2500 vs. 3500) and whether electric park brake is fitted.
Brake Wear Sensor – Front/Rear
VS30 CompatibleBrake pad wear sensor (indicator). Triggers dashboard warning at minimum pad thickness. Included with some OEM pad sets.
EGR Cooler-to-Valve Hose – OM642
VS30 CompatibleCoolant/exhaust hose connecting EGR valve to EGR cooler on OM642. Prone to cracking; common source of white smoke and coolant loss.
EGR Cooler Changeover Valve Hose – OM642
VS30 CompatibleHose between EGR cooler and changeover valve on OM642. Often replaced alongside the cooler-to-valve hose.
EGR Cooler Gasket – NCV3/VS30 OM642
VS30 CompatibleGasket set for the EGR cooler on the 3.0L V6 OM642. Replace whenever cooler or hoses are disturbed.
EGR Gasket – OM651 Valve to Recirculation Line
Not Compatible (OM651)EGR valve gasket between valve and recirculation line on 2.1L I4 OM651. Replace at every EGR service.
Oil Cooler Seal Kit – OM642 (Viton upgraded)
VS30 CompatibleFull Viton oil cooler seal/gasket kit for OM642. Common failure after ~120k miles. Requires removing turbo, manifold, and intercooler to access.
EGR Valve – OM642 (OEM)
VS30 CompatibleExhaust gas recirculation valve for 3.0L OM642. Carbon deposit clogging is extremely common; causes limp mode, poor economy, rough running.
EGR Valve – OM651 2.1L (OEM)
Not Compatible (OM651)EGR valve for 2.1L I4 OM651 Sprinter. Similar carbon clogging failure mode. Causes sticking and fault codes.
Intercooler-to-Intake Hose – OM642 (Passenger Side)
Verify FitmentIntercooler outlet hose (passenger side) connecting intercooler to intake air flap. Prone to cracking; causes boost leaks and limp mode.
Intercooler-to-Turbo Hose – OM642 (Driver Side)
Verify FitmentIntercooler inlet hose (driver/turbo side). Inspect both hoses together; cracking causes loss of boost and limp mode.
Turbocharger Gasket Set – OM642
VS30 CompatibleTurbo-to-exhaust manifold and downpipe gasket set for the OM642. Replace whenever turbo is removed.
Turbocharger Assembly – OM642 (Garrett)
VS30 CompatibleFull turbocharger replacement for 3.0L OM642. Garrett-supplied unit; billet compressor wheel available. Symptoms: white/blue smoke, power loss, whine.
DEF (AdBlue) Injector – SCR
VS30 CompatibleDiesel exhaust fluid injector for the SCR (BlueTEC) system. Failure causes fault codes, reduced power, or no-start if DEF tank reads empty.
DEF Tank Heater / Level Sensor Assembly
VS30 CompatibleCombined DEF tank heater and level/temp sensor. Heater failure in cold weather causes fault codes and can prevent engine start. Common VS30 issue.
NOx Sensor (Upstream/Downstream) – BlueTEC
VS30 CompatibleNOx sensor for SCR emissions system. Upstream and downstream variants differ. Failure triggers CEL, limp mode, and disrupts AdBlue dosing.
SCR Catalytic Converter (AdBlue Catalyst)
VS30 CompatibleSelective catalytic reduction catalyst in the exhaust aftertreatment system. Failure causes persistent fault codes and engine derate.
Fuel Injector Copper Seal Ring – OM642 (qty. 6)
VS30 CompatibleCopper crush washer sealing injector to cylinder head. Failure causes "black death"—combustion gas and carbon tar buildup. Replace at every injector removal.
Fuel Injector Copper Seal Ring – OM651
Not Compatible (OM651)Injector seat copper seal for OM651 2.1L. Same failure mode as OM642 version. Replace whenever injector is removed.
Fuel Injector – OM651 2.1L (Bosch)
Not Compatible (OM651)Bosch common-rail injector for 2.1L OM651 diesel. Symptoms: rough idle, smoke, misfires. Remanufactured units available.
Fuel Injector – OM642 3.0L (Bosch)
VS30 CompatibleBosch common-rail injector for 3.0L OM642. Expensive OEM; reman units widely used. Always replace copper seal ring on install.
Front Sway Bar End Link
Verify FitmentFront stabilizer/anti-roll bar end link. Common wear item; failure causes clunking over bumps. Replace in pairs.
Front Lower Control Arm Bushing
NCV3 OnlyRubber bushing for front lower control arm. Cracking and deterioration causes wandering steering and clunking over bumps.
Wheel Bearing Hub Assembly – Front
VS30 CompatibleFront wheel bearing/hub assembly. Failure indicated by humming/growling that changes with steering angle.
Wheel Bearing Hub Assembly – Rear
VS30 CompatibleRear wheel bearing assembly. Common mileage-related failure. Replace if play detected or humming present.
Tie Rod End (Outer)
VS30 CompatibleOuter tie rod end for front steering. Worn ends cause loose steering and uneven tyre wear.
MAF Sensor (Mass Air Flow) – OM642
VS30 CompatibleMass air flow sensor for the 3.0L OM642 intake system. Failure or contamination causes limp mode, P0101/P0102 codes, poor economy.
MAF Sensor – OM651 2.1L
Not Compatible (OM651)MAF sensor for 2.1L OM651. Similar failure symptoms to OM642 version.
Crankshaft Position Sensor – OM642
VS30 CompatibleCrank position sensor for the OM642 V6. Failure causes hard start, stall, and no-start conditions.
Intake Manifold Swirl Flap Motor – OM642
VS30 CompatibleActuator/motor for variable swirl flaps in OM642 intake manifold. Flap breakage can cause severe engine damage. Very common failure.
Coolant Temperature Sensor
VS30 CompatibleEngine coolant temperature sensor. Failure causes rough running, overheating faults, or incorrect gauge reading.
Glow Plug Relay / Pre-heat Controller – NCV3
NCV3 OnlyPre-heat relay module controlling all glow plugs. Early NCV3 design prone to blown fusible links; updated solid-state revision available. Verify VS30 fitment before ordering.
| Part Number | Part Name | Description | Price | Category | View |
|---|---|---|---|---|---|
| 6421800009 | Oil Filter – OM642 3.0L V6VS30 Compatible | Primary engine oil filter for 3.0L V6 OM642 diesel; includes gasket. OEM Mann HU821X. Replace every service interval (~10,000 mi).2007–2022 NCV3 & VS30, Sprinter 2500/3500 w/ 3.0L V6 OM642 | $13.99 | Maintenance & Filters | |
| 6421840025 | Oil Filter – OM642 (updated rev.)VS30 Compatible | Updated revision oil filter for OM642. Cross-reference to 6421800009. Check production date before ordering.2010–2022 NCV3 & VS30 w/ 3.0L V6 OM642 | $13.99 | Maintenance & Filters | |
| 6511800009 | Oil Filter – OM651 2.1L I4Not Compatible (OM651) | Engine oil filter for 2.1L 4-cylinder OM651 diesel. Multiple revision p/ns: 651-180-01-09, 651-180-03-09.2010–2018 NCV3 Sprinter w/ 2.1L I4 OM651 | $13.99 | Maintenance & Filters | |
| 0000903751 | Engine Air Filter (Mann C43121)VS30 Compatible | Engine air intake filter for 2010+ models. OEM: A 000 090 37 51. Replace every 20,000–30,000 mi or as indicated.2010–2022 NCV3 & VS30 Sprinter (all engines) | $31.99 | Maintenance & Filters | |
| 4478300000 | Cabin Air Filter – VS30 (Hengst)VS30 Compatible | Cabin air/pollen filter for the 3rd-gen VS30 Sprinter. Hengst E4927LC for auto A/C (HH4) or E4927LI for semi-auto (HH9). Replace annually or every 15,000 mi.2019–2022 VS30 Sprinter (all models, both HVAC variants) | $31.99–$34.99 | Maintenance & Filters | |
| 9068300318 | Cabin Air Filter – NCV3 (charcoal-activated)NCV3 Only | Recommended OEM charcoal-activated cabin filter for NCV3. Captures diesel/exhaust odors, pollen, and fine particulates. Alt p/n 906-830-02-18.2007–2018 NCV3 Sprinter 2500/3500 | $24.99 | Maintenance & Filters | |
| 9108300902 | Cabin Air Filter – W907 (charcoal-activated)VS30 Compatible | Recommended OEM charcoal-activated cabin filter for W907/VS30. Significant upgrade over standard particulate filter for traffic and camper use.2019–2022 W907/VS30 Sprinter | $36.99 | Maintenance & Filters | |
| 6420906052 | Fuel Filter – VS30/W907 OM642 (heated, Mann OEM)VS30 Compatible | OEM fuel filter for 2019+ VS30/W907 Sprinter with 3.0L V6 OM642. Includes integrated heating element and water-in-fuel sensor. Part of the VS30 Service A filter pack.2019–2022 VS30/W907 Sprinter w/ 3.0L V6 OM642 | $158.00 | Maintenance & Filters | |
| 6420906352 | Fuel Filter – NCV3 OM642 (5-pin)NCV3 Only | Latest-revision fuel filter; 5-pin plug for water sensor & heater, 13 mm and 15 mm fuel lines. NCV3 build dates 2012-2018 ONLY. MUST verify against existing connector before ordering.2012–2018 NCV3 w/ 3.0L V6 OM642 (verify by VIN) | $94.99 | Maintenance & Filters | |
| 6510902952 | Fuel Filter – NCV3 OM651 2.1LNot Compatible (OM651) | OEM fuel filter for Sprinter with 2.1L I4 OM651. Does NOT fit OM642 V6 vans.NCV3 Sprinter w/ OM651 2.1L only | $74.99 | Maintenance & Filters | |
| 6422000701 | Water Pump – OM642 (7-groove)VS30 Compatible | Mechanical water pump for 3.0L OM642 with 7-groove pulley. OE supplier (Graf). Includes gasket. Common failure ~100k+ miles.2008–2022 NCV3 & VS30 w/ OM642 (7-groove variant; verify) | $99.99 | Cooling System | |
| 6422001701 | Water Pump – OM642 (updated)VS30 Compatible | Updated water pump revision for OM642. Includes new gasket. Confirm groove count and production date before ordering.2008–2022 NCV3 & VS30 w/ OM642 | $108.00 | Cooling System | |
| 6512001602 | Water Pump – OM651 2.1L (switchable impeller)Not Compatible (OM651) | Switchable-impeller water pump for OM651. Failure can contaminate vacuum system; Mercedes specifies replacing vacuum reservoir and changeover valve simultaneously.2010–2018 NCV3 Sprinter w/ OM651 2.1L | $133.99 | Cooling System | |
| 6398350064 | Auxiliary Electric Water PumpVerify Fitment | Auxiliary electric pump (alt p/n 2118350264) circulates coolant through heater core. Runs when ignition is on. Common NCV3 failure.2007–2018 NCV3 Sprinter (all engine variants) | $83.99 | Cooling System | |
| 6422002015 | Thermostat Assembly – OM642 Late (unheated)VS30 Compatible | Unheated thermostat assembly for late-model NCV3 OM642 and VS30. Verify heated vs. unheated variant for your build date.Late NCV3 & VS30 w/ OM642 (verify by VIN/build date) | $49.99 | Cooling System | |
| 6422000815 | Thermostat Assembly – OM642 Early (unheated)NCV3 Only | Unheated thermostat assembly for early NCV3 OM642 models. Check production date.Early NCV3 Sprinter w/ OM642 (2007–~2010) | $49.99 | Cooling System | |
| 6422002115 | Thermostat Assembly – OM642 Early (heated)NCV3 Only | Heated thermostat (has electrical connector) for early OM642 NCV3. Verify by checking your existing part.Early NCV3 Sprinter w/ OM642 (heated variant; verify by VIN) | $66.99 | Cooling System | |
| 0029934296 | Serpentine Belt – OM642 (PK070801, 7-rib, 2035mm)VS30 Compatible | 7-rib accessory drive belt for 2008+ OM642 NCV3/VS30. 2035 mm length. Replace if cracked, frayed, or at belt kit interval.2008–2022 NCV3 & VS30 w/ OM642 (7-rib variant) | $41.99 | Drive Belt & Pulleys | |
| 6422001370 | Serpentine Belt Tensioner – OM642VS30 Compatible | INA OEM belt tensioner for 3.0L V6 OM642 drive system. Not for early 2007–some 2008 CDI ML/GL/R vehicles. Replace with belt.2008–2022 NCV3 & VS30 w/ OM642; also W906 Sprinter | $66.99 | Drive Belt & Pulleys | |
| 6422001070 | Serpentine Belt Idler Pulley – OM642 (qty. 2)VS30 Compatible | Flat idler/deflection pulley for the OM642 serpentine belt. INA OEM. Two required per vehicle. Replace bearings at belt service.2008–2022 NCV3 & VS30 w/ OM642 (need qty. 2) | $33.99 ea | Drive Belt & Pulleys | |
| 6422002670 | Aux Serpentine Belt Tensioner (Rear A/C or 2nd Alt)Verify Fitment | Tensioner for secondary drive belt powering optional rear A/C compressor (N63) or secondary alternator (N62) on NCV3.2007–2019 NCV3 Sprinter w/ rear A/C (N63) or 2nd alternator (N62) | $58.99 | Drive Belt & Pulleys | |
| 6421540802 80 | Alternator – Bosch Reman 220A (OM642)VS30 Compatible | Bosch remanufactured 220A alternator for the OM642 V6 - the recommended replacement when full capacity is required (cold-climate use, dual-battery house systems, conversions). Direct fit, OEM connector.2007–2022 NCV3/W907 Sprinter w/ 3.0L V6 OM642 | $566.99 | Charging & Starting | |
| 6421540802 | Alternator – Valeo 220A (OM642 OE)VS30 Compatible | Original-equipment Valeo 220A alternator. Stock fitment on most OM642 vans. Direct replacement using existing wiring.2007–2022 NCV3/W907 Sprinter w/ 3.0L V6 OM642 | $533.99 | Charging & Starting | |
| 0009062700 | Alternator – Valeo 180A (OM642 base)VS30 Compatible | Lower-output 180A alternator used on base/non-cold-package OM642 vans. Acceptable for stock loads; upgrade to 220A if running a house battery, inverter, or rear A/C.2007–2022 NCV3/W907 Sprinter w/ 3.0L V6 OM642 (base electrical) | $466.99 | Charging & Starting | |
| 0011596601 | Glow Plug – OM642 7V Ceramic (post 6/14/2012)VS30 Compatible | 7V ceramic glow plug (NGK CZ303) for OM642 V6. NCV3 switched to 7V plug after build date 6/14/2012; correct plug for 2019-2022 VS30. Replace all 6 together.2012–2022 NCV3 & VS30 w/ OM642 (after 6/14/2012 build date) | $29.99 ea | Glow Plug System | |
| 0011597101 | Glow Plug – OM642 Early 4.4VPre-2012 Only | Earlier-spec glow plug for 2007–mid-2012 OM642. OEM p/n 001-159-71-01-64. NOT for 2019-2022 VS30. Plugs can seize in the head; use anti-seize on install.2007–mid-2012 NCV3 w/ OM642 (pre 6/14/2012 build date) | $24.99 ea | Glow Plug System | |
| A0019971235 | Glow Plug Control Module – OM642VS30 Compatible | Glow plug control module/relay. Original design prone to blown fusible links; updated solid-state revision available. Replace when faulted.2007–2022 NCV3 & VS30 w/ OM642 | $133.99 | Glow Plug System | |
| 0044208320 | Front Brake Pads – Sprinter 2500VS30 Compatible | OEM front disc brake pad set for Sprinter 2500. Alt p/n 0054205220. Includes wear sensor where applicable.2010–2022 NCV3 & VS30 Sprinter 2500 | $91.99 | Brakes | |
| 0064208420 | Front Brake Pads – Sprinter 3500VS30 Compatible | OEM front disc brake pad set for Sprinter 3500. Includes wear sensor. Replace pads and rotors together for best results.2010–2022 NCV3 & VS30 Sprinter 3500/3500XD | $99.99 | Brakes | |
| 9064210012 | Front Brake Rotor – Sprinter 3500 (qty. 2)VS30 Compatible | Front ventilated brake rotor for Sprinter 3500. Sold individually; qty. 2 needed per axle. Inspect for minimum thickness.2010–2022 NCV3 & VS30 Sprinter 3500/3500XD | $91.99 ea | Brakes | |
| 0084205020 | Rear Brake Pads – Sprinter NCV3/VS30VS30 Compatible | OEM rear brake pad set. Alt p/n 9064210700. Verify fitment by model (2500 vs. 3500) and whether electric park brake is fitted.2010–2022 NCV3 & VS30 Sprinter 2500/3500 (verify variant) | $83.99 | Brakes | |
| 9064214200 | Brake Wear Sensor – Front/RearVS30 Compatible | Brake pad wear sensor (indicator). Triggers dashboard warning at minimum pad thickness. Included with some OEM pad sets.2010–2022 NCV3 & VS30 Sprinter 2500/3500 | $24.99 ea | Brakes | |
| 6421410483 | EGR Cooler-to-Valve Hose – OM642VS30 Compatible | Coolant/exhaust hose connecting EGR valve to EGR cooler on OM642. Prone to cracking; common source of white smoke and coolant loss.2007–2022 NCV3 & VS30 w/ 3.0L OM642 | $41.99 | EGR & Emissions | |
| 6421410583 | EGR Cooler Changeover Valve Hose – OM642VS30 Compatible | Hose between EGR cooler and changeover valve on OM642. Often replaced alongside the cooler-to-valve hose.2007–2022 NCV3 & VS30 w/ 3.0L OM642 | $33.99 | EGR & Emissions | |
| 6421420181 | EGR Cooler Gasket – NCV3/VS30 OM642VS30 Compatible | Gasket set for the EGR cooler on the 3.0L V6 OM642. Replace whenever cooler or hoses are disturbed.2007–2022 NCV3 & VS30 w/ 3.0L OM642 | $16.99 | EGR & Emissions | |
| 6511422380 | EGR Gasket – OM651 Valve to Recirculation LineNot Compatible (OM651) | EGR valve gasket between valve and recirculation line on 2.1L I4 OM651. Replace at every EGR service.2010–2018 NCV3 Sprinter w/ OM651 2.1L I4 | $16.99 | EGR & Emissions | |
| 6421800375 | Oil Cooler Seal Kit – OM642 (Viton upgraded)VS30 Compatible | Full Viton oil cooler seal/gasket kit for OM642. Common failure after ~120k miles. Requires removing turbo, manifold, and intercooler to access.2007–2022 NCV3 & VS30 Sprinter w/ 3.0L OM642 | $33.99 | EGR & Emissions | |
| 6421410110 | EGR Valve – OM642 (OEM)VS30 Compatible | Exhaust gas recirculation valve for 3.0L OM642. Carbon deposit clogging is extremely common; causes limp mode, poor economy, rough running.2007–2022 NCV3 & VS30 Sprinter w/ 3.0L OM642 | $249.99 | EGR & Emissions | |
| 6511400660 | EGR Valve – OM651 2.1L (OEM)Not Compatible (OM651) | EGR valve for 2.1L I4 OM651 Sprinter. Similar carbon clogging failure mode. Causes sticking and fault codes.2010–2018 NCV3 Sprinter w/ OM651 2.1L I4 | $216.99 | EGR & Emissions | |
| 9065280382 | Intercooler-to-Intake Hose – OM642 (Passenger Side)Verify Fitment | Intercooler outlet hose (passenger side) connecting intercooler to intake air flap. Prone to cracking; causes boost leaks and limp mode.2007–2009 NCV3 Sprinter w/ OM642 | $58.99 | Turbocharger & Intercooler | |
| 9065280282 | Intercooler-to-Turbo Hose – OM642 (Driver Side)Verify Fitment | Intercooler inlet hose (driver/turbo side). Inspect both hoses together; cracking causes loss of boost and limp mode.2007–2018 NCV3 Sprinter w/ OM642 (verify year) | $58.99 | Turbocharger & Intercooler | |
| 6420900480 | Turbocharger Gasket Set – OM642VS30 Compatible | Turbo-to-exhaust manifold and downpipe gasket set for the OM642. Replace whenever turbo is removed.2007–2022 NCV3 & VS30 Sprinter w/ OM642 | $41.99 | Turbocharger & Intercooler | |
| 6420901780 | Turbocharger Assembly – OM642 (Garrett)VS30 Compatible | Full turbocharger replacement for 3.0L OM642. Garrett-supplied unit; billet compressor wheel available. Symptoms: white/blue smoke, power loss, whine.2007–2022 NCV3 & VS30 Sprinter 2500/3500 w/ OM642 | $999.99 | Turbocharger & Intercooler | |
| 0004700093 | DEF (AdBlue) Injector – SCRVS30 Compatible | Diesel exhaust fluid injector for the SCR (BlueTEC) system. Failure causes fault codes, reduced power, or no-start if DEF tank reads empty.2010–2022 NCV3 & VS30 Sprinter w/ BlueTEC emissions (OM642/OM651) | $133.99 | DEF / SCR / AdBlue | |
| 0004901592 | DEF Tank Heater / Level Sensor AssemblyVS30 Compatible | Combined DEF tank heater and level/temp sensor. Heater failure in cold weather causes fault codes and can prevent engine start. Common VS30 issue.2013–2022 NCV3 & VS30 Sprinter BlueTEC models | $249.99 | DEF / SCR / AdBlue | |
| 0009054907 | NOx Sensor (Upstream/Downstream) – BlueTECVS30 Compatible | NOx sensor for SCR emissions system. Upstream and downstream variants differ. Failure triggers CEL, limp mode, and disrupts AdBlue dosing.2010–2022 NCV3 & VS30 Sprinter BlueTEC (OM642/OM651) | $166.99 | DEF / SCR / AdBlue | |
| 0004901392 | SCR Catalytic Converter (AdBlue Catalyst)VS30 Compatible | Selective catalytic reduction catalyst in the exhaust aftertreatment system. Failure causes persistent fault codes and engine derate.2010–2022 NCV3 & VS30 Sprinter BlueTEC models | $999.99 | DEF / SCR / AdBlue | |
| 6510170121 | Fuel Injector Copper Seal Ring – OM642 (qty. 6)VS30 Compatible | Copper crush washer sealing injector to cylinder head. Failure causes "black death"—combustion gas and carbon tar buildup. Replace at every injector removal.2007–2022 NCV3 & VS30 Sprinter w/ OM642 (qty. 6 needed) | $4.99 ea | Fuel Injectors & Seals | |
| 6510170221 | Fuel Injector Copper Seal Ring – OM651Not Compatible (OM651) | Injector seat copper seal for OM651 2.1L. Same failure mode as OM642 version. Replace whenever injector is removed.2010–2018 NCV3 Sprinter w/ OM651 (qty. 4 needed) | $4.99 ea | Fuel Injectors & Seals | |
| 0445116030 | Fuel Injector – OM651 2.1L (Bosch)Not Compatible (OM651) | Bosch common-rail injector for 2.1L OM651 diesel. Symptoms: rough idle, smoke, misfires. Remanufactured units available.2010–2018 NCV3 Sprinter w/ OM651 2.1L I4 | $483.99 ea | Fuel Injectors & Seals | |
| 0445115102 | Fuel Injector – OM642 3.0L (Bosch)VS30 Compatible | Bosch common-rail injector for 3.0L OM642. Expensive OEM; reman units widely used. Always replace copper seal ring on install.2007–2022 NCV3 & VS30 Sprinter w/ OM642 3.0L V6 | $416.99 ea | Fuel Injectors & Seals | |
| 9063300507 | Front Sway Bar End LinkVerify Fitment | Front stabilizer/anti-roll bar end link. Common wear item; failure causes clunking over bumps. Replace in pairs.2007–2018 NCV3 Sprinter 2500/3500 (verify VS30) | $41.99 ea | Suspension & Steering | |
| 9063501815 | Front Lower Control Arm BushingNCV3 Only | Rubber bushing for front lower control arm. Cracking and deterioration causes wandering steering and clunking over bumps.2007–2018 NCV3 Sprinter | $33.99 ea | Suspension & Steering | |
| 9064200083 | Wheel Bearing Hub Assembly – FrontVS30 Compatible | Front wheel bearing/hub assembly. Failure indicated by humming/growling that changes with steering angle.2007–2022 NCV3 & VS30 Sprinter (verify 2500 vs 3500) | $133.99 | Suspension & Steering | |
| 9064200183 | Wheel Bearing Hub Assembly – RearVS30 Compatible | Rear wheel bearing assembly. Common mileage-related failure. Replace if play detected or humming present.2007–2022 NCV3 & VS30 Sprinter 2500/3500 | $133.99 | Suspension & Steering | |
| 9054600115 | Tie Rod End (Outer)VS30 Compatible | Outer tie rod end for front steering. Worn ends cause loose steering and uneven tyre wear.2007–2022 NCV3 & VS30 Sprinter (verify left/right) | $49.99 ea | Suspension & Steering | |
| 0061530028 | MAF Sensor (Mass Air Flow) – OM642VS30 Compatible | Mass air flow sensor for the 3.0L OM642 intake system. Failure or contamination causes limp mode, P0101/P0102 codes, poor economy.2007–2022 NCV3 & VS30 Sprinter w/ OM642 | $99.99 | Electrical & Sensors | |
| 6511530028 | MAF Sensor – OM651 2.1LNot Compatible (OM651) | MAF sensor for 2.1L OM651. Similar failure symptoms to OM642 version.2010–2018 NCV3 Sprinter w/ OM651 | $99.99 | Electrical & Sensors | |
| 0005450432 | Crankshaft Position Sensor – OM642VS30 Compatible | Crank position sensor for the OM642 V6. Failure causes hard start, stall, and no-start conditions.2007–2022 NCV3 & VS30 Sprinter w/ OM642 | $49.99 | Electrical & Sensors | |
| 6420702726 | Intake Manifold Swirl Flap Motor – OM642VS30 Compatible | Actuator/motor for variable swirl flaps in OM642 intake manifold. Flap breakage can cause severe engine damage. Very common failure.2007–2022 NCV3 & VS30 Sprinter w/ OM642 | $133.99 | Electrical & Sensors | |
| 0009050804 | Coolant Temperature SensorVS30 Compatible | Engine coolant temperature sensor. Failure causes rough running, overheating faults, or incorrect gauge reading.2007–2022 NCV3 & VS30 Sprinter (various positions; verify) | $33.99 | Electrical & Sensors | |
| 9068302818 | Glow Plug Relay / Pre-heat Controller – NCV3NCV3 Only | Pre-heat relay module controlling all glow plugs. Early NCV3 design prone to blown fusible links; updated solid-state revision available. Verify VS30 fitment before ordering.2007–2018 NCV3 Sprinter w/ OM642 | $133.99 | Electrical & Sensors |
Sources: idparts.com · europaparts.com · blauparts.com · autohausaz.com · mbparts.mbusa.com